How To Clean Brushes On Hoover Dual Power Carpet Washer
Hello everyone well any of you lot who'd seen my previous video almost the trouble I had with my vac stool power carpet washer. This is just a little update to show you lot that the matter fingers-crossed has been resolved now this model in front of me here is the replacement that'southward kindly sent me a make new replacement for the faulty auto unfortunately before this ane arrived they did send me the reach model which was the wrong model.
I contacted backs and to their credit they speedily sent me the correct model which is the total home model the reach model is very like but it doesn't have the pretreatment kit that you get with a total abode the brush rolls are also majestic color on the attain model apart from the pretreatment kit they are the same Sheen'south.
The trouble I had with a faulty machine equally some other people have reported the drive belt has sort of moved forth on the pulley at the dorsum melted the pulley and the Machine ceased upward and at that place'southward been a aroma of called-for and sometimes smoke has come out of the automobile the smoke is caused by the called-for rubber it's nothing to do with the motor the motor is fine on this it was just the fact that the chugalug had shifted.
I've been assured that all new batches of this machine take the problem stock-still.
I'll simply point out a couple of things for you to check if yous've bought a VAX joule power carpeting washer or 1 of the very similar Hoover dual powers if you live in the USA this model very similar model to. This is available under the Hoover make.
What facts have done I've already loosened the screw.
At present I'm going to show you how to change the belt as well on this video in case you need to at some point the belt will stretch or snap and you volition need to replace it.
I'm going to go through how to do that for you.
Outset thing to do to get access to the belt is remove both chugalug guards I've already undone the screws to save some time but you'll observe at that place are 8 screws that you demand to undo marked one to 8.
They've got a little number and an pointer.
You need to kickoff undo this belongings it to the back.
These screw holes are numbered v six seven and eight.
Unscrew all the screws and and then you can remove the whole back part here now before I show yous the belt I just want to signal out a couple of things. This is the new modified part now if your machined you can check this if you lot turn upside downwardly and tin you meet in that location look in that location'due south a little green round sticker now I assume that symbolizes the fact that this machine is. Okay.
If yours has got that sticker on it'll exist alright just it might not accept a sick ROM and it might nevertheless be. Okay, the only other affair you demand to await at if y'all take this part off make sure yours oops at that place goes the spiral make sure yours has got a metal spindle here you need to see that there if yours doesn't have that I'd suggest y'all contact facts or Hoover depending on which country y'all bought this and ask them if they can send you one with this metal spindle because the faulty one I had didn't have this metallic spindle the attain model I was sent to know I could check information technology and again it had the sticker and had this extra metal spindle at present apparently this very pocket-size role plays a minor or.
A major role in keeping the chugalug in position.
When it's actually in place this forms part of thee when it'south down there it only stops the belt for moving on the caster which is what the problem was the chugalug shifted too far on the pulley it started rubbing against the side of the pulley and it information technology basically jarred and it'southward it kept on going pulley didn't keep going and it melted and that's what caused the trouble.
As long as yours has got this metallic spindle in y'all should be fine.
That I was pleased to run into that that there was a departure if I'd opened upwards the other model that was claimed to be from a new batch and at that place was no departure I would have been a bit dubious but considering of this I experience more confident that this machine is not going to fail in the aforementioned way as the first 1.
That'southward ane affair to cheque anyhow, back on to the replacing the brushroll.
The commencement thing y'all practise is remove the screws numbered v to 8 from that back part that also incorporates you lot wheel but that to one side and then you lot need to remove the other screws on the front part of the belt baby-sit they're numbered one to iv one little matter you may need two types of screwdriver it will take across a door Phillips screwdriver simply the thing I found on the screw position number seven here the shaft of this particular screwdriver wouldn't go all the fashion down to unscrew the spiral.
If you find that's the instance you lot might take to get yourself a screwdriver that's got a stop off like that 1 to be able to undo spiral number seven that's just a little matter I found.
Remember if you can't get information technology unscrewed it'south because your shafts also thick and apparently it's not normally a trouble only in this case that is a problem.
That'southward the showtime function you need to remove put that to one side so of course you've got your 2nd role.
Now we can see all the inside with the belt now either the machine isn't brushing properly because the chugalug stretched or it's snapped if it'due south snapped you just exist able to remove it hands but if it's just stretched and you noticing information technology's not bashing besides you'll demand to remove the belt off the 2 pulleys on the brushroll.
I'm just going to take the chugalug off the motor spindle at the back here to move the belts you just pull them out pull them out from the side where the belt is situated only pull pull it up and then out piece of cake now at this stage manifestly if you've been using your rug washer you might find y'all desire to give you a your chugalug.
Your castor is a skilful clean and also this cavity in hither requite that a expert wipe out and get any gunk considering you will afterwards a certain amount of use especially got pets there might be hair and rug fibers and all sorts of gunk particularly here as well where the castor rolls sitting on i side is to round areas and on the other side is a hexagonal piece.
Only while you're doing it brand sense spend a few minutes only clearing any gunk out of there before you fit your new chugalug.
In order to fit belts that's the new belt obviously it's not the new chugalug but that would be your new chugalug if you need to fit 1.
The simply affair you lot need to call up there's only 1 way these volition fit in because of grade you've got a round section here and not long section here.
Yous'll not be able to get the oblong into a round hole and vice versa and likewise you need to brand sure you've got the pulley side where the belt goes round don't driblet it you need to make sure that'due south on the side where the motor spindle is.
First thing to do after you lot've given information technology a adept clean locate the showtime blitz role merely slip your new belt over information technology first just keep information technology in position on the pulley at that place and and then yous just need to push or locate the other side into the slot offset the round slot and then just turn the end of the brushroll until the don't exercise that that'south um I'm just showing this because that's non what to exercise don't trap the belt.
Did that on purpose you encounter to show you not to do that make sure you've got the belt tight on the pulley at that place keep it in that position while you're locating the castor back into its position.
Yous might need to exercise a bit of jiggery-pokery hither to get information technology located there we are.
Now that's in identify the chugalug is costless to movement still and the brushroll moves hands.
And so we get the 2nd brushroll and the peak the process go along keep the belt around your pollex and again make sure the belts not going to get trapped when you push this turn the end until you lot find it's gone in and there we get they're in and they're rotating freely and the chugalug is non trapped information technology's in the channel where it should be.
Then all yous need to do is put the belt on the motor spindle just at the dorsum here you'll find it'due south piece of cake to practise it'due south not a large big effort to pull I've had some vacuum cleaners plainly this isn't a vacuum cleaner but it's a similar principle to an upright with a chugalug some I've taken a lot of boot forcefulness to stretch them back enough to go them over the spindle but you lot'll detect this one will just sit down over the spindle easy enough because the chugalug will tension when you've got the rear chugalug guard in identify and then the brushes volition rotate.
Before you screw anything dorsum again double cheque that everything is rotating freely double check the belt isn't caught and check exercise you take got the chugalug on the spin wolf it's.
Like shooting fish in a barrel for it to become dislodged just make sure it'due south centrally located one of import thing y'all need to remember when you identify the screw both chugalug guards back you lot must put the rear belt guard on outset the i with the wheel if y'all screw this one in first you lot'll find y'all tin't get that ane in and you'll know that from mistake I've washed that the instructions to exercise this are in the booklet you lot get but some people I know like to see a visual demonstration.
I thought this might help some folk out.
Allow's go into this it is tricky to locate this. This is the trickiest part of the whole thing you don't want to become information technology in the wrong position earlier yous first screwing whatever screws down you want to brand certain that it is properly located let me merely fit um remove the screws now one affair I'll just point out you equally well there are 2 unlike sizes of screw here you've got three screws and so a slightly shorter i at present the shorter one goes in position number is information technology's vi position half dozen.
If the screws come out and you're thinking I've got one that'due south shorter that goes in position six because it'south got a shorter distance if you lot put a longer screw into position six the scroop the actual terminate of the screw will poke out through the pinnacle and information technology could stop the motorcar from going into the upright and horizontal position because information technology's going to stick into the motor cover.
Information technology's very of import and this doesn't say in the instruction book it's very important that the shorter screw goes into position number six in that location.
We've taken all the screws out it'south a bit easier at present once again double check the belts in place and we need to write that'due south in information technology'south it's not going to stay in position because it'due south under some tension.
I'm just going to put the shorter screw in kickoff just to hold everything in place once again don't start screwing anything in if you're having any trouble because it might non be lined up like if you don't go information technology in properly then you could observe you're dandy the plastic and then it won't screw in at all.
I'thou non properly screwing them in I'm simply doing them part of the way just for speed obviously you will need to screw the bin now I demand to go the thinner screw driver shaft over for number vii make sure you spiral it in until you feel resistance don't over-tighten.
That'south the the dorsum chugalug baby-sit in identify then yous need to put the front belt garden once again locate it with a static brush to the front end that's information technology.
He'south earlier once more before yous screw anything down make sure it's in position correctly which information technology is and for speed I'm not going to go all the way with this just you lot go the idea y'all need to screw all four screws up together and then every bit a final check when yous've got the car lying down like this y'all'll find y'all tin retake the brushes only they're quite hard to motility and that'south because the brushes are at present being driven by the motor spindle the belt has been tightened past the action of screwing the chugalug guard this me about going into place.
It is engaged at present with the motor spindle.
That means when yous utilize the auto they'll rotate when it'due south in the upright position using the cleaning tools for example you'll find that the brushes are easy to move because now the belt is non tight on the motor spindle.
It means basically you can employ this motorcar with the hose and the belt will not drive the brushes which is a adept trivial safety feature.
That's how to modify a belt on a VAX dual ability carpet washer now hopefully because I've got a brand new machine with the correct role I'll exist able to do a full demo of this model.
Stay tuned very shortly I'll be demoing this cleaning carpets upholstery and we'll run into if that extra long hose does reach right to the summit of the stairs thanks for watching and I'll see you soon.
Source: https://cheapstery.com/review/how-to-change-the-belt-on-a-vax-dual-power-carpet-washer-28035
Posted by: swilleytheares.blogspot.com
0 Response to "How To Clean Brushes On Hoover Dual Power Carpet Washer"
Post a Comment